TAKER F722 BLS 100A 8S STACK

Changelog Oct 10, 2025: The flight controller firmware has been changed to: GEPRC_TAKER_F722_8S. If you still use the TAKERF722SE firmware for flash, you need to add the definition of “USE_BARO…

Specifications

$4999

OPTIONS: STACK, FC, ESC

Changelog Oct 10, 2025: The flight controller firmware has been changed to: GEPRC_TAKER_F722_8S. If you still use the TAKERF722SE firmware for flash, you need to add the definition of “USE_BARO USE_BARO_DPS310” before flash the firmware, and after burning the firmware, enter the following command in the CLI: set pinio_box = 40,41,255,255 save Firmware betaflight_4.5.2_STM32F7X2_GEPRC_TAKER_F722_8S(251009) Feature 1. Uses the mainstream STM32F722 chip 2. Equipped with the latest 42688-P gyroscope 3. 16M onboard black box storage 4. Integrated LC filter 5. Upgraded Type-C USB interface 6. Directly plugs into the DJI Air Unit 7. Paired with the TAKER H100_8S_BLS 100A 4IN1 ESC, providing a smooth flying experience 8. Simple and efficient installation method with shock absorbers for stable gyroscope performance 9. Dual independent BECs: 12V@3A and 5V@3A 10. Supports 8S Lipo batteries 11. Support direct insertion of 8 motors Specifications TAKER F722 8S Flight Controller MCU: STM32F722 IMU: ICM42688-P(SPI) Air Unit Connection: Direct plugs into DJI Air Unit Black Box: 16M onboard USB Interface: Type-C Barometer: Supported OSD: BetaFlight OSD w/ AT7456E chip BEC: 5V@3A,12V@3A dual BEC Firmware Target: GEPRC_TAKER_F722_8S Dimension: 38.5×38.5mm, Mounfing Hole Size: 30.5×30.5mm，φ4mm hole becomes φ3mm after using a silicone shock-absorbing circle Input Voltage: 3-8S LiPo UART: 6 UARTs Power Filter: Integrated LC filter Weight: 8.1g Includes TAKER H100_8S_BLS 100A 4IN1 ESC Input Voltage: 3-8S Lipo Ammeter: Support Calibration value: 200 Continue Current: 100A Burst Current: 105A (5 seconds) Support Protocol: Dshot 150/300/600 Size: 56.3*61.1 mm; hole: 30.5×30.5 mm; φ4 mm hole becomes φ3mm after using the silicone shock-absorbing ring. Weight: 28.8g Target: B_X_30 Includes 1 x TAKER F722 8S Flight Controller 1 x TAKER H100_8S_BLS 100A 4IN1 ESC 1 x Electrolytic capacitor(50V 4700uF) 1 x DJI connection cable(SH1.0 6pin 100mm) 2 x FC adapter cable(SH1.0 8pin 30mm) 1 x Receiver silicone cable(SH1.0 4pin 150mm) 1 x Camera connection cable(SH1.0-SH1.25 3pin 135mm) 1 x VTX connection cable(SH1.0 4pin-6pin 100mm) 1 x XT90 battery plug 1 x Red and black power cable(10AWG 240mm) 4 x M3*30 screws 4 x M3*25 screws 8 x Nylon nuts(M3) 12 x Silicone anti-shake pads(M3)