F4 Brushless Flight Controller and ESC V2.0 (BLHeli_32)

After several months of research, the greatest combination of F405 4S Brushless Flight Controller with BLHeli_32 16A ESC has been released which totally supports 4S power with a steady performance…

Specifications

After several months of research, the greatest combination of F405 4S Brushless Flight Controller with BLHeli_32 16A ESC has been released which totally supports 4S power with a steady performance . BLHeli_32 16A ESC is customized for Beta85X whoop drone. Meanwhile, Beta85X is the first micro drone with a BLHeli_32 ESC at present. BLHeli_32 is the 3rd generation ESC firmware after BLHeli and BLHeli_S, which is written for ESC’s that utilize 32-bit MCU. With the increase in processing power, faster input signals with lower latency and higher update rate would be possible in BLHeli_32, such as Dshot1200! Know more about BLHeli_32 ESC from Oscarliang’s blog . Check out Joshua Bardwell ‘s video to know every detail of BLHeli_32 SPECIFICATIONS OF FC CPU: STM32F405 (Overclock to 240MHz) Six-Axis: MPU6000 Size: 26mm x 26mm, whoop mounting pattern Firmware version: BETAFPVF405 (BEFH) OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode) RX3 and TX3 are with a uto inverter, supporting all RX including TBS Micro RX TX01 and RX01 ports are available for Frsky F-Port, DSM2/DSMX Buzzer solder pads Support programable LED like WS2812 etc Weight: 4.2g DIAGRAM FOR F405 4S FC SPECIFICATIONS OF ESC Support BLHELI_32 Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, Dshot1200 Input voltage: 3-4S lipo Cotinue current: 16A Peak current: 19A Firmware target: BETAFPV-16A-32bit MCU: STM32F051K66 Motor Connectors: 1.25mm header pins connector Weight: 4.4g (7.7g with XT30 cable) DIAGRAM FOR F405 4S FC PARTS UPDATED F405 4S FC board has added extra 4 p luggable ports for ESC, VTX, RX and LED board, convenient installation and decreasing the dislocated PIN mounting. Using single N-channel MosFETs on ESC board, which has a lower inner resistance. It is dual MosFETs on the original BLHeli_32 ESC board. Current sensor included. BLHeli_32 ESC is s oldering with 25V/220uf electrolytic capacitor, for reducing the defective rate caused by the instantaneous high voltage. HOW TO ASSEMBLE FC & ESC In order to be convenient for the installation and decrease the dislocated PIN mounting, we have added a port for ESC connection. Separate installation, in case the mutural vibration may interfere between FC and ESC. HOW TO ASSEMBLE FC & LED BOARD In order to be convenient for the installation, we have added a port for LED board connection. RECOMMENDED RECEIVER CONNECTION In order to be convenient for the installation, we have added a port for RX connection. All the ports are available on this board. So that you could connect any receiver you want on the board. For example. Frsky XM/XM+ Receiver Flysky Receiver TBS receiver DSMX receiver Here is the connection diagram with Frsky XM receiver or XM+ receiver Here is the connection diagram with Flysky receiver. Here is the connection diagram with Futabe-X-BOSS AC900 receiver. Here is the connection diagram with TBS Crossfire receiver. Here is the connection diagram with DSMX FullSpeed receiver. RECOMMENDED PARTS LIST Frame: Beta85X frame Motors: 1105 5000KV motors with 1.5mm header pins connector Battery: 450mAh 4S battery Props: 2″ 4-Blades Props PACKAGE 1 * F405 4S Brushless Flight Controller 1 * 16A BLHeli_32 ESC 1 * 4P Cable for RX 1 * 3 P Cable for LED board 4 * M1.4x4mm screws 4 * 1.2mm Anti-vibration ruber dampers